KiaDxb

it is minor but i still went to the mechanic and he confirmed that there was nothing to worry about

why dose the RPM spike when engine shifts from 2 to 3rd gear when accelerating my car is 2005 optima

chris both are doing good....

what next

It will be very expensive for sure depending on which year model you got atleast for 1000 or 1200 dhs. If car is new and under warranty let Kia motors fix this for you for free.

if i was to replacing the entire fuse box how much would it cost me????

Depending on wear on other three tire is too much then change all 4. If wear is less then get 1 and keep driving.

100% yes, if engine taking less air then fuel is burning rich and cause misfiring, stalling and excessive smoke too.

Injectors failing is quite rare. Better chase the short and fix it. Show to some good electrician and let him check it peacefully the whole harness.

i have punctured one of my tiers and need to replace it

the puncture cannot be repaired so i need to know if i change 1 and leave the other three as it is will it cause any harm to my car?

can a faulty vacuum leak be a possible cause of car misfiring and stalling?

there is a fault with the injectors or a short to the wire circuits between the injectors and PCM. what do i do

If its minor or mild noise, dont bother as all modern cars have too many relay clicking hear and there, If its loud show it to mechanic to check the gearbox.

Get your car computerize checked it seems like gear solenoid or gear connector is weak.

i hear a click when i reverse the car?

by avoiding this noise will i damage my gears?

what is this noise

when engaging in gear there is hesitation reverse or forward.what is the reason for this.

Not necessarily but if its worn out and have some aging issues then you should change it.

You just need to replace the crank seal or engine oil sump seal to stop the leak and nothing else need to be changed. Dont hear bullshit mechanics.

Spend some time at peace in shade and check all the fuses ad relays and change all the ones that are burnt and make note of it to check after week if it blows off again so that you can see electrcian and tell him this issue and aks him to diagnose everything.

It cud be possibe that these fuses just work fine so you are happy.

Airbag light i doubt will get fix with fuse or relay but horn and beeping for sure will get cured after good work. Airbag light cud be because of loose connection under driver seat, if not you need computer check to find the fault code and then clear it.

Avoid using puller as they won't work on these ones. The outer part is bonded to the inner. The pulley won't come off due to the timing sprocket and crank pulley sticking together. The best way I have found to get the pulley off is to spray penetrating oil where the timing sprocket roll pin enters the crank pulley, and also into the contact surface where the crankshaft contacts the pulley. Let it sit for a while. Try working the pulley side to side (by grabbing it with both hands on opposite sides, pull with one hand and push with the other). Sometimes this is enough. If not, I use a hammer and a thick brass punch, I'll tap on the center metal portion of the pulley at alternating points (12 then 6, 3 then 9, and so on). Between these two methods, it will come out for sure.

You have read it right bro, its ok type of SUV. Not too bad like few americans esp Ford and not too good like Japanese Toyota and Nissan.

And Kia service center is another story al together. Be careful with what they say and what they honor in warranty.

when changing the Axel is it imp. to change the bearing as well?

my 2004 sedona has a oil leak from a crack in oil sump can i repair it or does it need replaced.

please advice at the earliest

thank you

in my carnival 2003 the airbag light is stuck on, the horn doesn't work and now when i open the door it only beeps when ignition is on.is this some electrical fault or what

i am the owner if 2006 Kia Sportage and i am getting my timing belt changed but the this is that i cant remove the timing belt drive sprocket from the harmonic balancer as it is attached to it.

how do i do that

Its little backside of engine near the cylinder head area. More likely between cylinder number 6 and 8.